Layed a tile floor but tile got wet before I grouted and now looks dark. Will this go back to normal?

Create an rich, inviting outdoor patio space by installing tile over your ordinary concrete patio. There is a huge selection of styles and colors of tile for you to choose from. This wide variety will allow you to create the base for almost any decorating style.

What you'll need: * TSP: Tri-Sodium Phosphate is a popular cleaner. It helps remove dirt, grease and oil. You need to make sure that your surface is clean, not only for the mortar, but for your leveler and patch to stick as well.

* Concrete Patch/floor leveler: This will be used, depending on what kind of damage you have, to repair dips, cracks, or holes in your concrete floor. The floor must be level or your tiles will crack not long after you start using them for everyday traffic. * Concrete Sealer: This will be used after your repair work to ensure that the floor is a uniform surface and that it is resistant to condensation coming up through the concrete.

* Tile: Many styles, colors and materials are available. Whatever ... more.

Layed a tile floor but tile got wet before I grouted and now looks dark. Will this go back to normal? Can I grout now?

The tile only got wet with water. The thinset between the tiles seems to have dried. I have been running a dehumidifier all day and see no change in the dark color of the ceramic tile.

Asked by jimimi 41 months ago Similar questions: Layed tile floor wet grouted dark back normal grout Home > Home Improvement.

Similar questions: Layed tile floor wet grouted dark back normal grout.

Layed a tile floor but tile got wet before I grouted and now looks dark... Create an rich, inviting outdoor patio space by installing tile over your ordinary concrete patio. There is a huge selection of styles and colors of tile for you to choose from. This wide variety will allow you to create the base for almost any decorating style.

What you'll need: * TSP: Tri-Sodium Phosphate is a popular cleaner. It helps remove dirt, grease and oil. You need to make sure that your surface is clean, not only for the mortar, but for your leveler and patch to stick as well.

* Concrete Patch/floor leveler: This will be used, depending on what kind of damage you have, to repair dips, cracks, or holes in your concrete floor. The floor must be level or your tiles will crack not long after you start using them for everyday traffic. * Concrete Sealer: This will be used after your repair work to ensure that the floor is a uniform surface and that it is resistant to condensation coming up through the concrete.

* Tile: Many styles, colors and materials are available. Whatever you choose, make sure you add 10 percent to your square footage measurements when ordering. This will allow you to compensate for mistakes and for cut pieces.

* Mortar: Different kinds of tile require different types of mortar. Ask the sales representative who sells you the tile to help you choose the right one. * Trowel: A grooved trowel will be necessary to spread the mortar.

They are available with different sized grooves, so be sure to read the package directions on the mortar to ensure that you buy the right size. * Grout: Aside from being available in many different colors, grout comes in two varieties: sanded and un-sanded. The sanded variety is used when the gaps between your tiles is bigger than 1/8".

The sand gives the grout additional strength. Anything 1/8" or smaller will be just fine using un-sanded grout. You will most likely find that you want to use the un-sanded grout in the smaller gaps because it finishes much smoother.

Working sanded grout into a small gap can be frustrating. One word of warning: If you are using marble tile on your floor, never use sanded grout! Make sure you install it with 1/8" or smaller gap because you must use un-sanded grout with marble.

The sanded grout will scratch the surface of the marble tile and it is not repairable. * Grout Float: This is used to work the grout into the gaps between the tiles. Prepare the concrete: Before you begin to lay the tile over your concrete slab, make sure that the concrete is properly prepared.

Mix up a bucket of the TSP solution and use it to scrub the floor with a scrub brush and some elbow grease. Allow it to dry thoroughly. At this point, examine the floor and see if there are any cracks or pits that need to be fixed before you lay the tile.

Keep in mind, any uneven areas will allow the tile to rock back and forth, even after you install them. If the tile isn't lying flat, it will probably crack somewhere down the road. Take the time now to use the concrete patch or leveler and make sure that you have a flat surface with no defects.

Once your repairs have dried, take the time to seal the concrete. This will prevent moisture from settling under your tile, and will also allow your mortar to stick tightly. Plan the tile layout: As you get ready to begin laying the tile, you will need to decide ahead of time where you want to begin and end.

This is important because you will most likely have to cut pieces at the end to make them fit. Usually it is best if these cut pieces are in an inconspicuous place. Plan your starting spot accordingly to ensure that you can hide the cut pieces as well as possible.It is best to mark your starting point on the concrete floor and then snap a chalk line the entire length of the room.

You can use this line as a reference point to make sure that your first row is square and even. Mix the mortar: After you have decided where you want to begin, follow the instructions provided by the manufacturer and begin to mix the mortar. Don't mix too much in advance, as it will begin to set up on you before you can use it.

Using your grooved trowel, begin spreading the mortar over a small area. Never spread out more than what you can cover with three or four tiles at a time. If you run into trouble and have to stop or slow down, and you've got a huge area of mortar already spread, then it may start to set up before you can get the tile down.

Just do a little at a time and you will save yourself a potentially huge headache. Install the tiles: Lay the tiles into the mortar and, using the spacers, make sure you are running even with the chalk line.As you move on to the subsequent rows, use the spacers to keep your pattern square. Once a tile is set, try to avoid touching it again.

As soon as you make a small adjustment to one, you will find that you need to adjust them all. Get it right the first time and then don't touch it again. Sources: http://www.doityourself.com/stry/tileapatio .

Your tile should go back to its color, assuming it is good tile That usually indicates that water is getting under the tile because the grout is loose or old. It should return to normal color after a few days. If it does, then the water penetrating is for sure and you need to fix the grout and or caulking in that area of the floor.

Sources: My suggestion .

They are so dark & dirty looking, even with scrubbing.

I cant really gove you an answer,but what I can give you is a way to a solution, that is you have to find the anglde that you relate to or peaks your interest. A good paper is one that people get drawn into because it reaches them ln some way.As for me WW11 to me, I think of the holocaust and the effect it had on the survivors, their families and those who stood by and did nothing until it was too late.