I have a bathroom sink that I want to take out and it has pipes that go right up to the faucet. How do I take it out?

I have a bathroom sink that I want to take out and it has pipes that go right up to the faucet. How do I take it out? I have a bathroom sink that I want to take out and by the way I am a woman so I don't know a whole lot about sinks but my sin underneath has pipes that run right up to my faucet.

And I want to disconnect them but there is no sut off valves. I just want to put a new faucet in and a new cabinet with a sink witch I have all the stuff but I don't have the knowledge so if someone could tell me step by step how to disconnect my pipes under my sink so I can put my new sink in I would really appreciate it very much.. thank you robin Asked by teamom 22 months ago Similar questions: bathroom sink pipes faucet Business > Jobs.

Similar questions: bathroom sink pipes faucet.

Bathroom sink that I want to take out and it has pipes that go right up to the faucet.... #Step 1Determine what style of replacement faucet you need by inspecting your current faucet. The sink unit has molded holes that your new fixture must also fit. A faucet may be one-piece - a single metal unit with handle(s) and spout; or it may have three separate pieces - a spout and two separate handles.

The one-piece units come in two standard widths; four and eight inches. If it's a one-piece unit, it can have a single lever to mix hot and cold or two separate valves. The finish and style are a matter of personal choice, but the fit is defined by the sink (unless you want to replace the sink, too).

You may want to crawl under the sink to inspect the underside of the old faucet as well. Once you've figured this out, pick your new faucet and bring it home. #Step 2Open the cabinet under the sink, clear out everything that's there (leaving yourself plenty of floor room) and turn off the water with the two supply valves.

They'll probably have white plastic hoses disappearing behind the back of the sink. #Step 3Place the bucket and rags in a corner, lie on your back under the sink. Use the flashlight to inspect the setup under the counter.

Using an adjustable wrench (or, better, the proper-sized open-end wrench), loosen the supply lines. Remember, righty-tighty, lefty-loosey: turn the nuts counter-clockwise. The space will probably be very tight, so be patient, As soon as a line is loosened, it will leak water on the floor and in your face.

Place the loose end of the hose in the bucket and repeat the process with the second line. Use the rags to clean any water that slopped on the floor. If it's not readily apparent which line is hot water and which is cold, use some masking tape and a sharpie to mark them.

#Step 4Disassemble the sink stopper - a rod and lever arrangement, usually with a spring clip. Use a wrench to remove the rod from the drainpipe. This might end up being gooshy, so keep the bucket and rags nearby.

#Step 5Disassemble any other piping that connects valves to spout. This is unlikely unless you are replacing a three-piece set with two separate valves and the spout. #Step 6Ridgid Tool Basin Wrench (photo from Home Depot) Ridgid Tool Basin Wrench (photo from Home Depot)Plumbers use a special tool to loosen the nuts that are holding the works tightly in place.

This is a basin wrench, a relatively inexpensive tool. It's a pair of spring-loaded jaws at the end of a long handle with a T-Bar. The jaws flip over so that the wrench can be used both to tighten and loosen nuts.

Use the flashlight to locate the nuts, which may be covered with rust and precipitate from the water supply. Flip the jaws to the proper position and place them on on nut, turning the T-Bar to loosen the nut enough that you can begin to turn it with your fingers. Repeat the process on the other side and, if this is a three-piece set, the center nut as well.

If you don't own a basin wrench, they're fairly inexpensive (about 1/4th the cost of an hour of a plumber's time). Some rental stores also have them for hourly or daily rental. Some three-piece sets disassemble from the top, so before crawling underneath take the handles and trim apart.It there's a large nut on the "deck" of the sink, you can loosen it and let the faucet valves drop through instead of lifting them off.

#Step 7Lift the old faucet and/or valves off of the sink top and discard. If relatively new, collect all the parts as you go along and save for a donation to an organization such as Habitat for Humanity. #Step 8Clean the rust, soap scum, dried toothpaste, and dried plumber's putty from around the holes.

At this point, verify that the new faucet you've chosen will fit the hole configuration. Sources: http://www.ehow.com/how_4836870_change-bathroom-faucet.html .

How to Change a Bathroom Faucet 1. Step 1 Determine what style of replacement faucet you need by inspecting your current faucet. The sink unit has molded holes that your new fixture must also fit.

A faucet may be one-piece - a single metal unit with handle(s) and spout; or it may have three separate pieces - a spout and two separate handles. The one-piece units come in two standard widths; four and eight inches. If it's a one-piece unit, it can have a single lever to mix hot and cold or two separate valves.

The finish and style are a matter of personal choice, but the fit is defined by the sink (unless you want to replace the sink, too). You may want to crawl under the sink to inspect the underside of the old faucet as well. Once you've figured this out, pick your new faucet and bring it home.2.

Step 2 Open the cabinet under the sink, clear out everything that's there (leaving yourself plenty of floor room) and turn off the water with the two supply valves. They'll probably have white plastic hoses disappearing behind the back of the sink.3. Step 3 Place the bucket and rags in a corner, lie on your back under the sink.

Use the flashlight to inspect the setup under the counter. Using an adjustable wrench (or, better, the proper-sized open-end wrench), loosen the supply lines. Remember, righty-tighty, lefty-loosey: turn the nuts counter-clockwise.

The space will probably be very tight, so be patient, As soon as a line is loosened, it will leak water on the floor and in your face. Place the loose end of the hose in the bucket and repeat the process with the second line. Use the rags to clean any water that slopped on the floor.

If it's not readily apparent which line is hot water and which is cold, use some masking tape and a sharpie to mark them.4. Step 4 Disassemble the sink stopper - a rod and lever arrangement, usually with a spring clip. Use a wrench to remove the rod from the drainpipe.

This might end up being gooshy, so keep the bucket and rags nearby. 5. Step 5 Disassemble any other piping that connects valves to spout.

This is unlikely unless you are replacing a three-piece set with two separate valves and the spout. 6. Step 6 Ridgid Tool Basin Wrench (photo from Home Depot) Ridgid Tool Basin Wrench (photo from Home Depot) Plumbers use a special tool to loosen the nuts that are holding the works tightly in place.

This is a basin wrench, a relatively inexpensive tool. It's a pair of spring-loaded jaws at the end of a long handle with a T-Bar. The jaws flip over so that the wrench can be used both to tighten and loosen nuts.

Use the flashlight to locate the nuts, which may be covered with rust and precipitate from the water supply. Flip the jaws to the proper position and place them on on nut, turning the T-Bar to loosen the nut enough that you can begin to turn it with your fingers. Repeat the process on the other side and, if this is a three-piece set, the center nut as well.

If you don't own a basin wrench, they're fairly inexpensive (about 1/4th the cost of an hour of a plumber's time). Some rental stores also have them for hourly or daily rental. Some three-piece sets disassemble from the top, so before crawling underneath take the handles and trim apart.It there's a large nut on the "deck" of the sink, you can loosen it and let the faucet valves drop through instead of lifting them off.

7. Step 7 Lift the old faucet and/or valves off of the sink top and discard. If relatively new, collect all the parts as you go along and save for a donation to an organization such as Habitat for Humanity.

8. Step 8 Clean the rust, soap scum, dried toothpaste, and dried plumber's putty from around the holes.At this point, verify that the new faucet you've chosen will fit the hole configuration. 9.

Step 9 Remove the old tailpiece. You didn't even know that the metal bits in the bottom of the sink come out, did you! Start by using your pipe wrench to loosen the large nut on the drain about ten inches from the bottom of the sink (get your bucket ready, just in case).

Also loosen the first nut on the horizontal drain pipe - definitely be ready with the bucket. Loosen the large nut that snugs right up against the bottom of the sink, and begin to turn the pipe counterclockwise. The chrome ring at the bottom of the sink will unscrew from the pipe under the sink, and you can remove the two pieces.

You may need to tilt the assembly to remove the pipe; have your bucket ready for water. Sources: http://www.ehow.com/how_4836870_change-bathroom-faucet.html .

Change a Bathroom Faucet #Step 1Determine what style of replacement faucet you need by inspecting your current faucet. The sink unit has molded holes that your new fixture must also fit. A faucet may be one-piece - a single metal unit with handle(s) and spout; or it may have three separate pieces - a spout and two separate handles.

The one-piece units come in two standard widths; four and eight inches. If it's a one-piece unit, it can have a single lever to mix hot and cold or two separate valves. The finish and style are a matter of personal choice, but the fit is defined by the sink (unless you want to replace the sink, too).

You may want to crawl under the sink to inspect the underside of the old faucet as well. Once you've figured this out, pick your new faucet and bring it home. #Step 2Open the cabinet under the sink, clear out everything that's there (leaving yourself plenty of floor room) and turn off the water with the two supply valves.

They'll probably have white plastic hoses disappearing behind the back of the sink. #Step 3Place the bucket and rags in a corner, lie on your back under the sink. Use the flashlight to inspect the setup under the counter.

Using an adjustable wrench (or, better, the proper-sized open-end wrench), loosen the supply lines. Remember, righty-tighty, lefty-loosey: turn the nuts counter-clockwise. The space will probably be very tight, so be patient, As soon as a line is loosened, it will leak water on the floor and in your face.

Place the loose end of the hose in the bucket and repeat the process with the second line. Use the rags to clean any water that slopped on the floor. If it's not readily apparent which line is hot water and which is cold, use some masking tape and a sharpie to mark them.

#Step 4Disassemble the sink stopper - a rod and lever arrangement, usually with a spring clip. Use a wrench to remove the rod from the drainpipe. This might end up being gooshy, so keep the bucket and rags nearby.

#Step 5Disassemble any other piping that connects valves to spout. This is unlikely unless you are replacing a three-piece set with two separate valves and the spout. #Step 6Ridgid Tool Basin Wrench (photo from Home Depot) Ridgid Tool Basin Wrench (photo from Home Depot)Plumbers use a special tool to loosen the nuts that are holding the works tightly in place.

This is a basin wrench, a relatively inexpensive tool. It's a pair of spring-loaded jaws at the end of a long handle with a T-Bar. The jaws flip over so that the wrench can be used both to tighten and loosen nuts.

Use the flashlight to locate the nuts, which may be covered with rust and precipitate from the water supply. Flip the jaws to the proper position and place them on on nut, turning the T-Bar to loosen the nut enough that you can begin to turn it with your fingers. Repeat the process on the other side and, if this is a three-piece set, the center nut as well.

If you don't own a basin wrench, they're fairly inexpensive (about 1/4th the cost of an hour of a plumber's time). Some rental stores also have them for hourly or daily rental. Some three-piece sets disassemble from the top, so before crawling underneath take the handles and trim apart.It there's a large nut on the "deck" of the sink, you can loosen it and let the faucet valves drop through instead of lifting them off.

#Step 7Lift the old faucet and/or valves off of the sink top and discard. If relatively new, collect all the parts as you go along and save for a donation to an organization such as Habitat for Humanity. #Step 8Clean the rust, soap scum, dried toothpaste, and dried plumber's putty from around the holes.

At this point, verify that the new faucet you've chosen will fit the hole configuration. Sources: http://www.ehow.com/how_4836870_change-bathroom-faucet.html .

I have a bathroom sink that I want to take out and it has pipes that go right up to the faucet... Low water pressure in faucets is a very common problem. The source of a slow or clogged kitchen faucet can almost always be found inside the faucet. It usually takes a small amount of effort to get the water flow back to normal.

Read on to learn how to fix low water pressure. DEAR TIM: Several weeks ago our whirlpool faucet water pressure and volume dropped to half while I was filling the whirlpool with water. The pressure and volume slowly returned to normal.At the same time, our kitchen faucet pressure and volume dropped even more than 50 percent.

It has not returned to normal and gets worse each day. All other faucets seem to work fine and the toilets fill quickly. What happened?

What is wrong and is it expensive to correct? Patty J. , Sterling, VADEAR PATTY: Strange residential water pressure problems are far more common today than they were years ago.

Part of the dilemma has to do with the internal design of many modern faucet valves and another part of the problem is directly related to natural resource conservation measures. Years ago many standard kitchen, bath and shower faucets had rubber and plastic washers that contacted a circular valve seat inside the faucet.As you opened a faucet the washer would pull away from the valve seat creating a very large pathway for water to flow through. In many faucets the pathway was so big, a small, round BB could easily pass though the faucet and into the sink or a glass of water.

This older design allowed vast amounts of water to flow through a faucet and this is not a great thing when we have a growing population and limited fresh water supplies. But many of today's modern faucets have washerless cartridges inside the body of the faucet. The modern cartridge replaces the older washer and valve seat design which controls water flow.

The pathway through which water passes in these cartridges is much smaller than old faucets. Many of today's faucets also have an aerator at the end of the faucet. These devices are often made up of several small parts.

If you take the aerator apart, you will discover extremely small holes in round disks made of plastic or metal. The water flowing from the faucet must pass through these tiny orifices. Often the source of a household water pressure problem is right at your fingertips.

Simply remove the aerator tip on most faucets and inspect the parts for small pieces of sand, sediment and debris. PHOTO CREDIT: Tim CarterOften the source of a household water pressure problem is right at your fingertips. Simply remove the aerator tip on most faucets and inspect the parts for small pieces of sand, sediment and debris.

PHOTO CREDIT: Tim CarterTo meet federal and state guidelines to conserve water, many modern faucets and fixtures have flow restrictors that limit the amount of water that can pass through the faucet in a given amount of time. These restrictors often have tiny holes that limit the amount of water flow. I am convinced the drop in water volume and pressure at the two faucets was caused by small pieces of sediment or some other debris that clogged a passageway within the valve cartridge and/or the tiny orifices within the aerator and or a flow restrictor.

This is an extremely common problem for many homeowners. The sediment can form within a faucet or its parts depending upon the hardness of your water. Sediment also forms as a scale on the inside of municipal water supply pipes and the water lines inside your home.

Pieces of this sediment can break off and be transported through the water lines as water moves towards a faucet. Small pieces of sand or rocks can enter a water system, especially those of people who use a private well. These can block the pathways within your faucets.

These low water pressure and flow problems are very common just after a water main break in a municipal water system. Sand, dirt and other debris can enter municipal piping systems when a water main fractures. Once the water main is repaired, this debris is transported through the water system and can end up in your home.

Small shavings of piping, soldering flux, sediment, etc.Can also be carried through your own pipes when repairs are made to your plumbing system or new piping is added at your home. Problems can also happen by simply turning on or off a main or secondary water control valve within your home by a plumber who might be installing a new faucet or performing a repair. Sources: http://www.askthebuilder.com/612_Low_Water_Pressure_in_Faucets.shtml .

If it's just dripping, you can usually just replace a washer or other seal. If you'd like to replace the whole thing, though, don't worry. The procedure is pretty straightforward, especially if you have the right tools.

Edit Steps 1. 1 Three openings under a lavatory faucet. Three openings under a lavatory faucet.

Look at your sink. Check to see how many openings there are and how far apart they are. You may have to look underneath to be sure.

For bathroom faucets, in particular, the two handles may be a single unit with the spout or they may be spread apart from it. You will need this information to choose the correct replacement. Ads by Google Bathroom Products Factory Confident sourcing at HKTDC's award winning e-Marketplace.

It's free! Supplier.hktdc.Com/evolutionindl 2. 2 Obtain a replacement faucet.

You'll probably be using this faucet a long time, so it's worth investing in a good-quality faucet. * It's possible to spend anywhere from about $20 to $500 and up on a faucet. Read reviews and decide for yourself how much of what you are paying is for quality and how much is for designer names/styling and fancy features.

3.3 Review the instructions that come with the faucet. They can range from detailed and helpful to minimal and frustrating. When in doubt, defer to the manufacturer's instructions rather than those you find elsewhere.4.

4 Consider buying a basin wrench for under $20.It's a tool designed to reach way up behind your sink and remove the two big nuts on each side of the faucet that hold the faucet tight against the sink. If you can't easily loosen the nuts by hand or with the tools you have on hand, a basin wrench can make the job easier. 5.5 Clear the area.

Clear the area. Remove everything from under the sink and store it well out of your way. Sources: http://www.wikihow.com/Replace-a-Kitchen-or-Bathroom-Faucet .

" "I changed a valve in my bathroom and had to drain the water out of the pipes now I have noise in pipes" "My bathroom sink smells when the water runs out. If the vent area has something in it , how do I clean it?" "My super hasn't fixed the perpetual faucet leak in the bathroom for 6 months now. He keeps on putting it off.

" "What paint color for bathroom that will have black vanity and red glass vessel sink/faucet?" "Does this product (Water fall glass faucet C33) have a matching bathroom light fixture? " "I am looking for a hose that will attach to a bathroom sink faucet. Any suggestions?" "How do I get rid of the smell from my hot water faucet in the bathroom?

" "do you clean the overflow drain in your bathroom sink?

How do you cap off bathroom sink plumbing permanetly.

I changed a valve in my bathroom and had to drain the water out of the pipes now I have noise in pipes.

My bathroom sink smells when the water runs out. If the vent area has something in it , how do I clean it?

My super hasn't fixed the perpetual faucet leak in the bathroom for 6 months now. He keeps on putting it off.

I am looking for a hose that will attach to a bathroom sink faucet. Any suggestions?

I cant really gove you an answer,but what I can give you is a way to a solution, that is you have to find the anglde that you relate to or peaks your interest. A good paper is one that people get drawn into because it reaches them ln some way.As for me WW11 to me, I think of the holocaust and the effect it had on the survivors, their families and those who stood by and did nothing until it was too late.